The case of the iMac screen that mysteriously blacks out

Glenn Fleishman
14 August, 2017
View more articles fromthe author

Cecil Usher wants to give his granddaughter a 2010-era 27-inch iMac. However, there’s a problem.

The screen goes completely black and stays that way for no apparent reason, sometimes shortly after turning the iMac on, and sometimes not at all. Sometimes the screen simply never turns on and stays completely black. When the screen stays on, it looks perfect.

Cecil took the iMac to an Apple-authorised service centre that couldn’t replicate the problem and their diagnostics found nothing wrong. However:

We took the machine home and the screen came on at startup and within a minute went blank. This has been happening for over a year.

The iMac works with an external display just fine, whether or not the internal display is blank.

Without laying hands on the computer, my guess is this is an electrical fault that has a thermal component. While I haven’t seen this recently, in my youth – when I was more hands-on with soldering irons and circuits – it was relatively common to have faults that only materialised under certain circumstances in which heating or cooling caused expansion or contraction that produced a temporary gap in whatever conductive material was passing electricity.

(As a child, my family had a colour TV set, but when it heated up, it shifted to black and white. We had to bang it to get colour back. Banging the set jarred the discontinuity in the solid-state circuit that did colour decoding. Yes, I’m that old.)

With modern manufacturing, that sort of nonsense is much less likely, but given that moving the iMac into a different location made the problem impossible to replicate lends credence. In movement, it might have been jarred, or the repair facility might be heavily air conditioned or not at all, while Cecil’s home is the opposite.

I suspect the repair shop only ran hardware diagnostics via software, which wouldn’t reveal this, and didn’t open it up. It might cost $100 or more to have someone qualified crack the case and look for signs of failure, at which point unless they’re handy with a soldering iron and it’s something that can be fixed with molten tin and lead, it won’t be worth repairing.

Just to on the safe side, I always suggest the following as part of diagnosing video issues:

  • Boot in safe mode. This sometimes reveals problems with video cards that don’t materialise otherwise. That seems unlikely here, but if the iMac runs for hours in safe mode without the screen blanking, there’s a software-related problem.
  • Reinstall macOS over the existing installation. If there’s any system software issue, as bizarre as that might be, this would solve it.

Unfortunately, an external monitor is likely the best way to keep using this iMac if the two above troubleshooting options don’t help further.

More advice

Since we first posted this article last week, many readers wrote in with additional advice.

One correspondent realised that the issue was absolutely basic: the vent holes on the back and bottom of his 2011 iMac were covered in dust. He removed the dust, and a thermal sensor stopped shutting down the display. You can use a vacuum brush attachment or compressed air. (If you use compressed air, remember to power down the Mac, and place it in a position so that you keep the can of air upright. Otherwise, you can spray liquid out of the can that evaporates so rapidly it causes freezing on surfaces it touches, and can damage the case and the screen.)

Reader B. Jefferson said a friend’s iMac had a similar problem due to an imperfect upgrade by a previous owner. “There was a gap in the thermal paste that prevented the screen from making full contact with a sensor along the bezel. That gap caused periodic screen blackouts. Pressing on the affected spot could restore light temporarily.” You’d need to find a shop that was willing to disassemble and reassemble a Mac to fix this problem.

Yet another had an issue with a 2009 iMac’s backlighting: sometimes the monitor works, but when the backlighting fails, you can’t see anything on the display. While he replaced the screen, the problem came back. He noted that in his case, putting the iMac to sleep through a keyboard shortcut (Control–Shift–Power button or Control–Shift–Media [CD/DVD] Eject) or by pressing and quickly releasing the iMac’s power button. Waking it would re-activate the backlighting, at least temporarily. Running it with a dimmer setting for screen brightness also worked.

Tye found that an Epson printer that used Wi-Fi for network connections appeared to cause an iMac blackout. Moving the printer further away reduced the frequency of blackouts, but didn’t entirely eliminate them. We know that improperly shielded monitor cabling can allow Wi-Fi to affect displays and even system crashes, so this is another variable to try to eliminate when troubleshooting.

One Comment

One person was compelled to have their say. We encourage you to do the same..

  1. Rob Weaver says:

    Had a similar problem a few weeks ago with my late 2009 27 inch iMac. The shop was able to replicate the fault a couple of times, but then it performed normally. They told me they thought it a fault with the graphics but recommended it would be too expensive to find and fix. So I brought it home. Same fault has occurred a few times, but switching it off at the mains and leaving it for a couple of minutes seems to work. I have everything backed up and will replace the machine if it gets worse. I’ll probably opt for the most powerful Mac Mini with a good monitor I already have, because I am not sure that the newer, slimmer iMacs would last as long, given that everything has been shoehorned into an even thinner case.

Leave a Comment

Please keep your comments friendly on the topic.

Contact us